/ Products - Page 2

  • Floor Jack Mount

    $15.00 – $40.00

    Mounting system developed to store and secure your floor jack in the race trailer. This gets it off the floor and secure for transit.
    Includes Hitch Pin and Cotter Pin to secure jack in place.
    Includes sheet metal screws to affix to trailer wall.

    All Versions $50
    Version A:
    Fits older 1.5 ton “Pittsburgh Automotive Low Profile Aluminum Racing Floor Jack” with the single pump cylinders.

    Version B:
    Fits current “PITTSBURGH AUTOMOTIVE 1.5 Ton Low-Profile Aluminum Racing Floor Jack with RAPID PUMP” with dual pump cylinders
    Fits “DAYTONA 1.5 ton Professional Racing Series Aluminum Floor Jack with RAPID PUMP”

    Version C:
    Fits “DAYTONA 1.5 ton Ultra-Low-Profile Lightweight High-Performance Aluminum Racing Jack with RAPID PUMP”
    Fits “PITTSBURGH AUTOMOTIVE 2 ton Low-Profile Aluminum Racing Floor Jack with RAPID PUMP”

    Version D:
    Fits “PITTSBURGH AUTOMOTIVE 3 ton Low-Profile Aluminum Racing Floor Jack with RAPID PUMP”
    Fits “ARCAN 3 ton quick rise aluminum floor jack with dual pump pistons and reinforced lifting arm”
    Fits “Torin AT83000 low profile economic aluminum service jack”

    Optional jack handle holder (Version “Backing Handle”) mounts behind the main bracket utilizing the same mounting screws.
    Optional jack handle holder (Version “Small Handle”) mounts separately in a location of your choosing using its own attaching screws. Additional holes sized for Sharpies.

    Select options Done

  • MagAir Helmet Air System

    $30.00 – $35.00

    Introducing the MagAir helmet forced-air system.

    Designed to be affordable, these 3d printed adapters allow endurance racing teams to add forced air cooling to every driver’s helmet at an affordable price. The magnet retention system allows for rapid driver changes and quick egress.

    The vehicle side components contain rare earth magnets. The magnets allow safe storage of the hose on the roof of most vehicles when not in use and during driver changes.

    The helmet side components contain mild steel bushings with a retention flange, ensuring disconnects are intentional. Side loads will not affect magnetic retention strength.
    Your expensive helmet air kit purchased from the helmet manufacturer will not be damaged. MagAir adapters attach via non-destructive and reversible methods.

    Options:
    Helmet Side:
    1. Stilo – This adapts from the Round ST5 helmet air kit to the MagAir system. Clamps onto the Helmet and is retained with two screws.
    2. Roux – This adapts from Roux Helmets oval helmet air kit to the MagAir system. Attaches via Heat/Friction
    3. Simpson – This adapts from Simpson Helmets round barbed air kit to the MagAir system. Requires drilling the factory rivet.

    Vehicle Side
    4. 1.5″ CCW Hose – Adapts from MagAir system to a 1.5″ Spiral Wound air hose. CCW is the most common winding direction. Left-Hand threads to tighten adapter into the hose.
    5. 1.5″ CW Hose – Adapts from MagAir system to a 1.5″ Spiral Wound air hose. CW is offered for the rare hose wound in the Right-Hand thread direction.
    6. 1″ Clamp Hose – Adapts from MagAir system to a 1″ bulb, allowing clamping of 1″ id hose to the adapter. Fits common Forced-Air system adapters.

    Select options Done

  • E46 Touring Roof Rail Delete Kit

    $35.00

    3d Printed kit to patch the holes left in the drip rails when removing the roof-rack rails on an E46 touring.

    The community asked for a solution to the $800+ euro roof rail trim. This is a result of that request.

    This kit consists of 16 pieces and is enough to complete a single car.

    Each side has 4 penetrations that must be patched.

    Clip: Qty 6 per car. Used for the front large, front small, and middle holes
    Rear X-clip: Qty 2 per car. Used for the rear hole to support the rear cover. Left and Right are bespoke.
    Large Cover: Qty 4 per car. Used for the front large and middle holes.
    Small Cover: Qty 2 per car. Used for the front small holes.
    Rear Cover: Qty 2 per car. Used for the rear holes only. Marked “R”.

    October 2022 Update: Print Material switched from PETG to ASA for higher tolerance to temperature. If you ordered a kit prior to Sep 2022 and experience shrinkage, please contact me.

    Installation Instructions

    Add to cart Done

  • TPS Adapter Bracket – 3d Printed ABS

    $20.00

    TPS Adapter 3d printed from ABS.

    Hardware included – Embedded nuts with bolts. Reuse original TPS screws to attach to throttle body.

    The TPS needed is from a E36, PN 13631721456 (Not included)
    The wiring may be modified by re-pinning the stock connector or via a short adapter harness. The adapter harness provides ease of install and lower risk. The stock wiring is brittle and oil soaked at this point, and the e36 TPS faces the wrong direction.

    If you have a 3d printer and wish to make this yourself – STL file is free for download Here

    Add to cart Done

  • E46 Light Control Module (LCM / LSZ) Extension Cable

    $15.00

    10-Pin ribbon cable that allows you to reinstall the front panel of the factory E46 light switch to the dash after relocating the rear portion of the light switch.

    Usually necessary when roll cage dash bar interferes with the rear portion of the light module.

    Pre-Terminated – standard length is 12″, different lengths available upon request

    3d Printed bracket available separately

    Add to cart Done

  • Roux Helmet Forced Air Adapter

    $15.00

    3d Printed adapter to convert from the Roux helmet forced air (oval shape) to the round Stilo helmet shape.

    The Stilo helmet shape is compatible with many off-the-shelf .875 rubber boots allowing connection to an array of common forced air pumps.

    Sized for a compression fit. Simply heat the adapter with a heat gun or hair dryer and slip over the roux fitting. When cool, the adapter requires significant force to remove.

    Add to cart Done

  • E46 Light Control Module (LCM / LSZ) Relocation Bracket

    $10.00

    3d Printed bracket that allows you to reinstall the front panel of the factory E46 light switch to the dash after relocating the rear portion of the light switch.

    Usually necessary when roll cage dash bar interferes with the rear portion of the light module.

    Made from ASA, will not warp when left in a hot race-car on grid.

    Extension Cable available separately

    Add to cart Done

  • E30 Oil Level Sensor Replacement Connector

    $10.00

    Replacement connector for your E30 M20 oil level sensor E30 Oil Level Sensor Pigtail This replaces the crumbled connector attached to the sensor in the oil pan. The connector is labeled with 1,2,3 Sensor Side wiring: Pin 1 = Blue/Violet = Static Level Pin 2 = Blue/White = Dynamic Level Pin 3 = Brown/Orange =…

    Add to cart Done

  • ABS Rebuild Tool – 3d Printed Solenoid Vice

    $10.00

    Disposable tool designed to hold the ABS solenoids without damaging them in any vice.
    This eliminates the need for soft jaws or making something from wood.

    3d Printed from ABS plastic by me, Made in North Carolina.

    Color will vary based on what filament I currently have loaded in the printer.

    If you have a 3d printer and wish to make yourself – STL file is free for download Here

    Add to cart Done

  • Stilo Drink Tube Drain

    $6.00

    This is the correct fitting needed to allow draining of your drink tube without removing the helmet’s quick disconnect fitting.

    After the race hook this up so your drink hose doesn’t stay full and get nasty between events.

    This is for my Stilo ST5 helmet integral drink kit, also tested on a SA2015 ROUX helmet with integral drink kit.

    Add to cart Done